SpeedyBee F405 Mini Stack – F405 V3 FC + 35A 3-6S BLHeli_S 4-in-1 ESC – 20×20

SpeedyBee F405 Mini Stack – F405 V3 FC + 35A 3-6S BLHeli_S 4-in-1 ESC – 20×20

The SpeedyBee F405 Mini BLS 35A 20×20 Stack features an upgraded F405 flight controller chip and a built-in Bluetooth chip for seamless wireless Betaflight tuning

Out of stock

6,199

Out of stock

Same Day Shipping

Mon-Sat til 2.00PM on Most orders

Provide Warranty

Seller & Manufacturer Warranty

Svg Vector Icons : http://www.onlinewebfonts.com/icon

Best Prices

Best Prices in India

Best Customer Support

Industry leading support

The SpeedyBee F405 Mini BLS 35A 20×20 Stack features an upgraded F405 flight controller chip and a built-in Bluetooth chip for seamless wireless Betaflight tuning. This board comes with a 4-level battery voltage display and a built-in barometer and supports connectivity to all DJI Air Units. It offers 4 available UART ports, and a dual BEC setup with 5V 2A and 9V 3A outputs.

The 35A 4-in-1 BLHeli_S Mini ESC provides four synchronized outputs with a continuous current of 35A, delivering strong power to drive all 2-4 inch and lightweight 5-inch quadcopters via a 4-6S battery. Equipped with a TVS transient suppression diode onboard, it better absorbs surge voltage, providing enhanced protection for the ESC.

Features

  • TVS transient suppression diode for surge voltage absorption and enhanced protection
  • Compatibility with 2-4 inch and lightweight 5-inch quadcopters
  • Four synchronized outputs with a continuous current of 35A
  • Dual BEC setup: 5V 2A output and 9V 3A output
  • Built-in Bluetooth chip for wireless Betaflight tuning
  • Supports connectivity to all DJI Air Units
  • Upgraded F405 flight controller chip
  • 4-level battery voltage display
  • 35A continuous current output
  • Supports 4-6S battery
  • 4 available UART ports
  • Built-in barometer

Specifications

SPEEDYBEE F405 V3 20X20 FLIGHT CONTROLLER

  • DJI Air Unit Compatibility: Compatible with all DJI Air Units (DJI O3/RunCam Link/Caddx Vista/DJI Air Unit V1). Use specific solder pads for pin-to-pin connection. Note: UART1 is used for OSD and SUBS(R2) is used for SBUS receiver signal input
  • BLE Bluetooth: Supported. Used to connect with the SpeedyBee App for flight controller and ESC parameter configuration. Note: MSP switch on UART 4 must be turned on and set to a baud rate of 115200 for Bluetooth functionality
  • Wireless FC Firmware Flashing: NOT Supported. Connect to Betaflight configurator on PC for firmware update
  • Wireless Blackbox Download & Analysis: NOT Supported. Connect to Betaflight configurator on PC for blackbox analysis
  • Current Sensor Input: Supported. For SpeedyBee BLS 35A V2 ESC, set Scale=250 and Offset=-500
  • Power Input: 3-6S LiPo. Powered through 8pin harness G, V wires or G, V pads from bottom side
  • BOOT Button: Supported. Forces FC to enter DFU mode for firmware flashing
  • 3.3V Output: Supported. Designed for 3.3V input receivers. Up to 500mA current load
  • 4.5V Output: Supported. Designed for radio receiver and GPS module. Up to 1A current load
  • Mounting: 20 x 20mm, 3.5mm hole diameter. Compatible with M2 and M3 screws/Silicone grommets
  • I2C: Supported. DA & CL pads on the front side for magnetometer, sonar, etc
  • Traditional Betaflight LED Pad: Supported. Used for WS2812 LEDs
  • Supported Flight Controller Firmware: BetaFlight (Default), INAV
  • BetaFlight Camera Control Pad: Yes. CC pad on the front side
  • ESC Signal: M1 – M4 wires or soldering pads on the bottom side
  • UART: 6 sets. UART1-6 with dedicated purposes
  • Firmware Target Name: SPEEDYBEEF405MINI
  • Buzzer: BZ+ and BZ- pad used for 5V Buzzer
  • 5V Output: 4 groups. The total current load is 2A
  • 9V Output: 1 group. The total current load is 3A
  • DJI Air Unit Connection Way: Direct soldering
  • Dimension: 30(L) x 32(W) x 7.8(H)mm
  • Smart Port / F.Port: Not Supported
  • ESC Telemetry: UART R5 (UART5)
  • Blackbox: 8MB Onboard Flash
  • RSSI Input: Not Supported
  • OSD Chip: AT7456E chip
  • IMU(Gyro): ICM42688P
  • USB Port Type: Type-C.
  • WIFI: Not supported
  • Barometer: Built-in
  • MCU: STM32F405
  • Weight: 9.6g

SPEEDYBEE 35A BLHELI_s MINI V2 4-IN-1 ESC

  •  Mounting: 20 x 20mm ∅3.5mm hole size, compatible with M2 and M3 screws/Silicone grommets
  • Power Output: VBAT (Battery voltage, used to power the flight controller)
  • Current Sensor: Support (Scale=250 Offset=-500)
  • ESC Telemetry: Not supported
  • Burst Current: 45A (5 seconds)
  • Dimension: 35 * 35 * 5.5mm
  • ESC Protocol: DSHOT300/600
  • Continuous Current: 35A * 4
  • Firmware: BLHeli_S J-H-40
  • Power Input: 3-6S LiPo
  • Weight: 7.2g

Includes

  • 1x SpeedyBee F405 V3 20×20 Flight Controller
  • 1x SpeedyBee 35A BLHeli_S Mini V2 4-in-1 ESC
  • 5x M2 Silicone O-Ring
  • 5x M5 Silicone O-Ring
  • 5x M2 Anti Vibration Silicone Grommets
  • 5x M3 Anti Vibration Silicone Grommets
  • 1x 8-Pin JST cable 30mm
  • 1x 35V 470uf Capacitor
Weight 60 g

Reviews

There are no reviews yet.

Be the first to review “SpeedyBee F405 Mini Stack – F405 V3 FC + 35A 3-6S BLHeli_S 4-in-1 ESC – 20×20”

Same Day Shipping

Mon-Sat til 2.00PM on Most orders

Provide Warranty

Seller & Manufacturer Warranty

Svg Vector Icons : http://www.onlinewebfonts.com/icon

Best Prices

Best Prices in India

Best Customer Support

Industry leading support

Please login to post questions

Question:

when will this be back in stock?

karthick_bhojan
05-Nov-2024

Answer:

Answer awaiting...

SpeedyBee F405 Mini Stack
SpeedyBee F405 Mini Stack – F405 V3 FC + 35A 3-6S BLHeli_S 4-in-1 ESC – 20×20

Out of stock

We are temporarily not accepting Orders

    There is nothing much we are happy than helping you out with the latest FPV gears, and offering top notch aftersales support. But we have stopped accepting orders till further notice due to ill-defined reasons. 

Thank you for all the support you have given us in the past. You are the reason why we are called India’s Premier and Finest FPV Store. So Don’t hold Back; We will be back in:

Days
Hours
Minutes
Seconds