TBS Podracer AIO

TBS Podracer AIO

The TBS Podracer AIO is a powerful whoop board designed to cater for TBS Pro32 Nano VTX and TBS Crossfire / Tracer Nano RX with direct pin-header installation. The result is a clean, compact and lightweight core for your build.

Out of stock

8,499

Orders placed before are shipped on same day

Out of stock

TBS partnered with Zeez to make this awesome whoop AIO. Introducing the the TBS Podracer AIO, the board is designed to cater for TBS Pro32 Nano VTX and TBS Crossfire / Tracer Nano RX with direct pin-header installation. The result is a clean, compact and lightweight core for your build..

The FC is equipped with F4+MPU6000 and the ESC is capable of True 30A current running BLHeli32. This board is versitle enough to run on your cinewhoop, 4/5″ racer like the podracer and longrange cruiser like the TBS Aureo.

FC side

  • Mounting holes: 25.5×25.5 mm / M2 holes
  • Crossfire/Tracer RX CH1&2 > Uart 2  /  Pro32 Nano VTX > Uart 1 / Uart 1(RX) – unavailable.
  • Up to 6S input
  • 5V BEC up to 1.2A continuous
  • STM32F411 MCU (Support BetaFlight, EmuFlight)
  • MPU6000 Gyro/ACC
  • OSD chip Onboard (AT7456E)
  • 2 available UART
  • LC Filter for 5V VTX and Camera
  • Direct solder connection for TBS Nano RX and TBS Unify Pro32 Nano
  • Support programmable LED like WS2812 etc
  • Built-in current sensor

ESC side

  • Signal support: PWM, Oneshot125, Oneshot42, Multishot, Dshot150, Dshot300, Dshot600
  • Input voltage: 2S-6S Lipo
  • Continuous current: 30A
  • Peak current: 35A
  • ESC firmware: BLHELI 32
  • PWM Frequency Range: 24KHz up to 96KHz

GPS Installation

Because of the phyiscal limitations, installing a GPS module to the FC will require a few extra steps to remap the board’s resources.
Note: The following steps will disable LED and FC’s SmartAudio and use as softserial for GPS.

        1. Flash the board with Target: STM32F411

        2. Download the Config file [HERE]. Then load it the board.

        3. Wire the GPS as shown

Includes

  • 1 x TBS Podracer AIO
  • 1 x Capacitor
  • 1 x AWG cables set with shrink tubes
  • 4 x mounting gromets
  • 1 x XT60 (Male)
  • 1 x XT30 (Male)
  • 1 x Pinheaders set for TBS VTX and RX

Reviews

There are no reviews yet.

Be the first to review “TBS Podracer AIO”

Same Day Shipping

Mon-Sat til 2.00PM on Most orders

Provide Warranty

Seller & Manufacturer Warranty

Svg Vector Icons : http://www.onlinewebfonts.com/icon

Best Prices

Best Prices in India

Best Customer Support

Industry leading support

We are temporarily not accepting Orders

    There is nothing much we are happy than helping you out with the latest FPV gears, and offering top notch aftersales support. But we have stopped accepting orders till further notice due to ill-defined reasons. 

Thank you for all the support you have given us in the past. You are the reason why we are called India’s Premier and Finest FPV Store. So Don’t hold Back; We will be back in:

Days
Hours
Minutes
Seconds